AIS
Layer & Lever · Part 1

Part 1, on your own drive.

All 15 Part 1 episodes in one download: each video in 1080p with no ads, the Python script that builds the model in Blender, the STL for your slicer, and the notes for printing it. Before Part 1 was built, every script was run again in Blender 5.2 and rebuilt exactly the model beside it.

Watch the series on YouTube

One-time purchase. Every model is checked in Blender; none has been test-printed yet.

Layer & Lever Part 1, bound as a cloth book with a gold-foil cover

What’s in Part 1

One folder per episode, each with the same four things: the video, the script, the STL, and a README with the print notes. Scripts from episode 4 on come with layerlever.py, the module they load check() from. Only in Part 1: every Part 1 helper in one module, with a test that checks it against all 15 models, and a bonus print: a hinged box with a snap lid.

  1. 01 Print-in-Place Hinge: Prints Already Assembled (Blender + Python) Watch the episode
  2. 02 Why Your Blender Model Is Tiny in the Slicer (and the Fix) Watch the episode
  3. 03 Is It Printable? Check a Blender Model with Python Watch the episode
  4. 04 3D Printable Gears in Blender: Involute Teeth from Python Watch the episode
  5. 05 Make Two Gears Mesh: Center Distance and Gear Ratio Watch the episode
  6. 06 Print-in-Place Gear Fidget: Two Gears, One Print Watch the episode
  7. 07 Snap-Fit Lid in Blender: Clips That Click Watch the episode
  8. 08 Printable Bolt and Nut in Blender: Threads from a Helix Watch the episode
  9. 09 Printed Holes Come Out Small: Polyholes and Teardrops Watch the episode
  10. 10 Print-in-Place Ball Joint in Blender Watch the episode
  11. 11 Print-in-Place Chain: Links That Never Need Assembly Watch the episode
  12. 12 Living Hinge Flip-Top Box in Blender Watch the episode
  13. 13 3D Printed Springs: Flexure, Coil and Spiral Watch the episode
  14. 14 Can an AI Build a Printable Hinge? (Blender MCP Test) Watch the episode
  15. 15 One Print, Five Mechanisms: the Part 1 Sampler Watch the episode

Free, or Part 1?

The models stay free. Buying Part 1 keeps the whole part in one place, videos included.

Free, with your email

  • ·Each episode’s STL and script, on the series page the morning it airs
  • ·The videos on YouTube
  • ·The Printer Dial-In Kit

Part 1

$79 · one-time
  • ·All 15 episodes in one zip, nothing to unlock
  • ·Every video in 1080p with no ads, to keep and watch offline
  • ·A README per model: what it teaches, how to run it, how to print it
  • ·Every script run again in Blender 5.2 before Part 1 was built
  • ·Only in Part 1: every Part 1 helper in one module, and a bonus hinged box with a snap lid

Get Part 1

$79 · one-time, no subscription

Buy Part 1 · $79
  • ✓15 episodes: the video, the script, the STL and the print notes for each
  • ✓Videos in 1080p, no ads, yours to keep
  • ✓Every script re-run in Blender 5.2: each rebuilt exactly its model
  • ✓Bonus: a hinged box with a snap lid, plus every Part 1 helper in one tested module
  • ✓One zip, about 400 MB, with a START HERE guide
  • ✓Your download link always serves the newest version
  • ✓Email support at [email protected]

After checkout, your download link arrives by email (card) or appears on the confirmation page (crypto). Keep it: it starts a fresh download each time you open it, and it always serves the newest version.

Checked in Blender, not test-printed: your printer gets the final word. For personal use: print these models, change them and learn from them. Selling prints of these designs isn’t covered by this purchase.

Blender is a registered trademark of the Blender Foundation. Layer & Lever is an independent series from AIS and is not affiliated with or endorsed by the Blender Foundation.